Skip to main content

+15V / 1A Regulated Power Supply using uA723

electronic circuit diagram

This is the design diagram of +15V / 1A regulated power supply using uA723.
Circuit operation: The supply receives +20VDC from the rectifier / filter section (diode bridge). This is applied to pins 11 and 12 of the IC uA723, as well as to the collector of the 2N3055 series-pass transistor. The output voltage is simpled through R1 and R1, providing about 7V with respect to ground at pin 4. The reference terminal at pin 6 is tied directly to pin 5, the noninverting input of the error amplifier. For fine tuning output voltage, a potensiometer can be installed between R1 and R2. A 100 pF capacitor to pin 4 furnishes gain compesation for the amplifier.



Base drive to the 2N3055 pass transistor is furnished by pin 10 of the uA723. Since the desired output of the power supply is 1A, the maximal current limit is set to 1.5A by the resistor Rsc whose value is 0.433 Ohm.

A 100uF electrolytic condensator is used for ripple voltage reduction at the output. A 1K Ohm output resistor give stability for the power supply while in "no load" condition. The 2N3055 pass transistor have to be mounted on an adequate headsink for it stability and prevent overheating.

Comments

Popular posts from this blog

LM317T Voltage Regulator Circuit with Pass Transistor

This is the schematic diagram of voltage regulator circuit with pass transostor. The regulator is based regulator IC of LM317T. The LM317T output current can be raised by utilizing an additional power transistor (on circuit, it is 2N2955) to share a portion of the total current. The amount of current sharing is established with a resistor placed in series with the LM317 input and a resistor placed in series with the emitter of the pass transistor. In the above scheme design , the pass transistor will start conducting when the LM317 current reaches about 1 ampere, due to the voltage drop across the 0.7 ohm resistor. Current limiting happens at about 2 amperes for the LM317 which will drop about 1.4 volts across the 0.7 ohm resistor and make a 700 millivolt drop across the 0.3 ohm emitter resistor. Thus the total current is limited to about 2+ (.7/.3) = 4.3 amperes.

Sealed Lead Acid (SLA) 12V Battery Charger with Current Limiting

This is the circuit design of Smart Sealed Lead Acid (SLA) 12V Battery Charger featuretwith Current Limiting. The charger uses a two step process for charging SLA batteries – a current limited ‘fast’ mode followed by a constant voltage ‘float’ mode. Maximum charging current is 1A. An onboard LED indicates when the charger is in ‘fast’ mode. When the LED goes out the battery is charged and the charger has switched to ‘float’ mode.

Unregulated Dual Polarity Power Supply

This is the schematic diagram of Unregulated Dual Polarity power supply . Unlike 78xx and 79xx dual polarity regulated power sypply and LM317/LM337 dual polarity regulated power supply which have limited current output and voltage (have limited supply power), this unregulated power supply will give you more power. This kind of circuit usually used for power amplifier which need high supply power, or as high current lead acid battery charger (single polarity only). The component value is flexible refer to your needs. For example: if you need power supply for 100W amplifier, then the component value are: Transformer: 3A minimum (center tap) Diodes: 3A diode (1N5401, 1N5402, 1N5403 etc) Electrolytic capacitor: 4x minimum of 4700uF/50V (the higher is better - check the capacitor voltage, change it for higher voltage. example: use 63V capacitors for 45V power supply output.)